Welcome to Qinhuangdao Boostsolar Photovoltaic Equipment Co., Ltd. !
Qinhuangdao Boostsolar Photovoltaic Equipment Co., Ltd.
Full automatic tabber and stringerHome>Products

BSSW3600 Double Track Automatic Stringer

Product categories:Full automatic tabber and stringer
Product display:Double track, automatic,Actual Capacity≥3400pcs/h

 

 

Specification:

1.Capacity Actual Capacity≥3400pcs/h

2.Compatibility:156×156mmMono, Poly; Standard configuration for 4BB and 5BB, 3BB selective assembly. 1/2 Cell-156mm Mono, Poly, for optional

3.Cell Thickness:180μm 300μm

4.Bus Bar Width:1.0mm 1.8mm,Bus Bar Thickness:0.1mm0.26mm

5.Cell Breakage Rate: ≤0.2%(Take Class-A cell as standard, except unqualified incoming material)

6.Bus bar Positioning Accuracy ≤0.2mm98%

7.Rate of Pseudo Soldering ≤0.1%Pseudo Soldering pieces/Total soldering piecesBus Bar Tensile test: 180°Direction PullingAverage Value≥1.8N4 bus bar cellUptime: ≥98% Continuous production of class-A solar cell, based on standard bus barCell Spacing: 2mm20mm adjustable; Cell Distance Error: ±0.3mm

8.Cell String Straightness Less than 0.5mm testing on 10 pcs/strings, (excluding poor printed cell )

9.String Length Variation :±0.6mm

10.Flux Coating Method: Spray flux to cell main grid line

11.Welding Technique: Non-contact infrared welding

12.Temperature Control Method: closed-loop control, Heating base plate, controllable with real time monitorroom temperature 400°C

13.Camera Software: Independent intellectual property rights, easy to learn and use, free upgrade

14.Cell Positioning Method : Main grid /cell edge positioning; Parallelism deviation≤±0.1mm; angle deviation≤±0.01°

15.Defect Detecting: Edge damage, broken corner, fracture, grid poor printing, angle etc

16.Bus Bar Bending Function: Z-type bending, position adjustable

17.Bus Bar Lap Joint Cutting Function: Automatic lap joint cutting after bus bar replacement

18.Bus bar Coil U/Weight ≤10KG

19.Maintenance Time:Less than 20 minutes per day, refer to the manual details

20.Machine Life: 10 Years

Safety performance Requirements and Realization

1.Equipped with an emergency button, when an emergency situation occurs, the operator should just push the emergency stop button to actualize emergency shut down;

2.Grating ruler protection, when the operator makes accidental entry, the equipment will be stopped;

3.The electrical components can get reliable protection if an over-current, overload or short circuit happened;

4.When the air source, vacuum, temperature and the sensors come to an abnormal situation, it will trigger visual and audible alarm;

5.All potential safety hazard areas with high temperature, rapid mechanical transmission and mechanical arms will be posted with safety warning signs.

Safety performance Requirements and Realization

1.Equipped with an emergency button, when an emergency situation occurs, the operator should just push the emergency stop button to actualize emergency shut down;

2.Grating ruler protection, when the operator makes accidental entry, the equipment will be stopped;

3.The electrical components can get reliable protection if an over-current, overload or short circuit happened;

4.When the air source, vacuum, temperature and the sensors come to an abnormal situation, it will trigger visual and audible alarm;

5.All potential safety hazard areas with high temperature, rapid mechanical transmission and mechanical arms will be posted with safety warning signs.

Installation, Commissioning and Training Plan

1. In order to make the installation and commissioning go fast and smooth, Party B shall get done following preparatory works before the arrival of Party A’s installing and commissioning personnel:

Get ready the water, electricity and air source.

After the machine being delivered to Party B’s factory, Party B shall place the machine in its proper installing location in the workshop.

2. After the machine arrives factory and all the preparation works been finished, Party A will start to install the commission the equipment within two days after party A received the written notice from party B,

specific arrangements as following:

Install the equipment , adjustment the horizontal level and height;

Link the gas circuits of each unit , test the movement of air cylinders, manipulators and other parts;

Link with the layout machine and other automatic line equipments;

After installation and commissioning, the machine should take continuous idle dry running for 72 hours;

Adjust the string welding process, and start small quantity production stage.

Get into the normal production stage, and begin to train the relevant technical operators .

  Previous:  Single Rail Stringer BSSW1600-IV  
  Next:  Nothing

PRIVACY POLICY